Site-directed Mutagenesis using PCR

Site-directed Mutagenesis using PCR Michael P. Weiner, Tim Gackstetter, Gina L. Costa, John C. Bauer, and Keith A. KretzFrom: Molecular Biology: Current Innovations and Future Trends. Eds. A.M. Griffin and H.G.Griffin. ISBN 1-898486-01-8 1995 Horizon Scientific Press , PO Box 1, Wymondham, Norfolk, U.K.In vitro site-directed mutagenesis is an invaluable technique for studying protein structure-function relationships, gene expression and vector modification. Several methods have appeared in the literature, but many of these methods require single-stranded DNA as the template. The reason for this, historically, has been the need for separating the complementary strands to prevent reannealing. Use of PCR in site-directed mutagenesis accomplishes strand separation by using a denaturing step to separate the complementing strands and allowing efficient polymerization of the PCR primers. PCR site-directed methods thus allow site-specific mutations to be incorporated in virtually any double-stranded plasmid; eliminating the need for M13-based vectors or single-stranded rescue.

Several points should be mentioned concerning site-directed mutagenesis using PCR. First, it is often desirable to reduce the number of cycles during PCR when performing PCR-based site-directed mutagenesis to prevent clonal expansion of any (undesired) second-site mutations. Limited cycling which would result in reduced product yield, is offset by increasing the starting template concentration. Second, a selection must be used to reduce the number of parental molecules coming through the reaction. Third, in order to use a single PCR primer set, it is desirable to optimize the long PCR method. And fourth, because of the extendase activity of some thermostable polymerases it is often necessary to incorporate an end-polishing step into the procedure prior to end-to-end ligation of the PCR-generated product containing the incorporated mutations in one or both PCR primers.

A protocol is provided as a facile method for site-directed mutagenesis and accomplishes the above desired features by the incorporation of the following steps: (i) increasing template concentration approximately 1000-fold over conventional PCR conditions; (ii) reducing the number of cycles from 25-30 to 5-10; (iii) adding the restriction endonuclease Dpn I (recognition target sequence: 5-Gm6ATC-3, where the A residue is methylated) to ｓｅｌｅｃｔ against parental DNA (note: DNA isolated from almost all common strains of E. coli is Dam -methylated at the sequence 5-GATC-3); (iv) using Taq Extender in the PCR mix for increased reliability for PCR to 10 kb; (v) using Pfu DNA polymerase to polish the ends of the PCR product, and (vi) efficient intramolecular ligation in the presence of T4 DNA ligase.

Protocol. PCR-based Site Directed Mutagenesis

• Plasmid template DNA (approximately 0.5 pmole) is added to a PCR cocktail containing, in 25 ul of 1x mutagenesis buffer: (20 mM Tris HCl, pH 7.5; 8 mM MgCl2; 40 ug/ml BSA); 12-20 pmole of each primer (one of which must contain a 5-prime phosphate), 250 uM each dNTP, 2.5 U Taq DNA polymerase, 2.5 U of Taq Extender (Stratagene).
• The PCR cycling parameters are 1 cycle of: 4 min at 94 C, 2 min at 50 C and 2 min at 72 C; followed by 5-10 cycles of 1 min at 94 C, 2 min at 54 C and 1 min at 72 C (step 1).
• The parental template DNA and the linear, mutagenesis-primer incorporating newly synthesized DNA are treated with Dpn I (10 U) and Pfu DNA polymerase (2.5U). This results in the Dpn I digestion of the in vivo methylated parental template and hybrid DNA and the removal, by Pfu DNA polymerase, of the Taq DNA polymerase-extended base(s) on the linear PCR product.
• The reaction is incubated at 37 C for 30 min and then transferred to 72 C for an additional 30 min (step 2).
• Mutagenesis buffer (1x, 115 ul, containing 0.5 mM ATP) is added to the Dpn I-digested, Pfu DNA polymerase-polished PCR products.
• The solution is mixed and 10 ul is removed to a new microfuge tube and T4 DNA ligase (2-4 U) added.
• The ligation is incubated for greater than 60 min at 37 C (step 3).
• The treated solution is transformed into competent E. coli (step 4).