详细BAC DNA Isolation

A. Culture Growth:

1.For BAC isolation for shotgun library construction:

Pick a smear of colonies and inoculate 3 ml TB medium containing the appropriate antibiotic.

Grow the culture for 8 hours, 37 degrees C, shaking at 250 rpm in the Floor Shaker to produce the "starter culture".

Add 1.8 ml of TB medium to each well in the 96 deep well block.

Dilute culture 100 fold with TB and innoculate 5 μl of the diluted culture into each well using the Eppendorf repeater pipette.

Grow the BAC clone in the Floor Shaker for 18 hours at 37 degrees C shaking at 350 rpm.

2.For BAC or Fosmid isolation for end sequencing:

Using the Hydra96, inoculate 2 μl of the BACs or Fosmids from their glycerol plate stocks into either a 96 or 384 well shallow plate.

Incubate at 37 deg C overnight in a static growth chamber without shaking to produce the "starter culture".

Add 1.8 ml of TB medium to each well in the 96 deep well blocks using the Eppendorf repeater pipette.

Using the Hydra96, inoculate 2 μl from this "starter culture" (either 96 or 384 well shallow well plates) into 96 well deep well blocks containing 1.8 ml of TB medium in each well.

Grow the BAC clone in the Floor Shaker or HiGro for 18 hours at 37 degrees C shaking at 350 rpm.

Add 18 μl of 10x induction solution for amplification of the pEpiFOS-5 and incubate for an additional 5 hours at 37 degrees C shaking at 350 rpm.

B. DNA Isolation:

1.Centrifuge the blocks at 3000 rpm for 10 mins. Discard the supernatant.

2.*DO NOT FREEZE* the cell pellets but continue with the next steps in the isolation without pausing.

3.Add 300 μl of TE-RNaseA/T1 (TE-RNaseA/T1 is: 10 mM Tris-HCl, pH 7.6; 1 mM EDTA; 42 ug/ul RNase A; 0.04 U/ul RNase T1) to each well using the Hydra (The Hydra will add 300 μl by adding 150 μl twice).

4.Incubate on the table top microtiter shaker at speed of 7 until for 20 minutes to fully resuspended the cells.

5.Add 300 μl of lysis buffer (1% SDS, and 0.2 N NaOH) to each well, using the Hydra. Incubate on microtiter shaker at speed of 4 until a clear lysate is developed, takes approximately 15 minutes.

6.Add 300 μl 3M NaOAc, pH 4.5 to each well using the Hydra. Shake in the HiGro at 37degC and a shaker setting of 400 rpm for 30 minutes.

7.Freeze the blocks at -70 degrees C overnight.

8.Remove the blocks from freezer and thaw. Centrifuge at 3200 rpm for 45 mins in a Beckman CS-6R table top microtiter plate centrifuge.

9.Transfer 500 μl of supernatant from each well to new blocks using the Hydra (The Hydra will transfer 500 μl by transferring 250 μl twice).

10.Add 500 μl of isopropanol to each well using the manual Eppendorf repeater pipette.

11.Centrifuge the blocks at 3000 rpm for 30 mins. in the Beckman CS-6R table top microtiter plate centrifuge to collect DNA . Decant the supernatant. Invert on a paper towel.

12.Dissolve the pellet by adding 40 μl of steril double distilled water (instead of 10 μl of 10:1 TE to each well which should be added if the BAC or Fosmid DNA is to be used for shotgun cloning) using the Hydra followed by shaking on the table top for 20-30 minutes to dissolve DNA .

13.For isolating BACs and Fosmids for end sequencing skip to the last step, i.e. electrophores an alaquot of the dissolved DNA on a 1% agarose gel as the second acetate cleanup step is not necessary. Typically 10 μl of this 40 μl DNA solution is used for each end sequencing reaction with 1:8 Big Dyes or Amersham ET mixes, 2 μl of universal primer from a 6.5 umolar primer stock solution, in a final volume of 14 μl followed by 60 cycles of cycle sequencing amplification and loading onto the ABI 3730xl.